/ Register

EVO X Engine in a Lancer GTS?

Discussion in '8G Lancer - Performance' started by Carvs, Nov 8, 2009.

Page 1 of 2
  1. Carvs

    Carvs Active Member

    Hey there,

    So, as the title says I am looking into an engine swap from a 4b12 to an EVO X 4b11t. I wanted to know if this was in anyways possible, and get some thoughts and comments on the subject. Thanks :)
     
    Carvs, Nov 8, 2009
    #1
  2. vmo91

    vmo91 Well-Known Member

    it is possible but you'll probably have to upgrade your transmission too!
     
    vmo91, Nov 8, 2009
    #2
  3. LancerRA09

    LancerRA09 Well-Known Member

    Especially if you have the CVT
     
    LancerRA09, Nov 8, 2009
    #3
  4. LiX

    LiX Well-Known Member

    + clutch if manual, turbo, exhaust manifold, intercooler, ECU ! Not to mention you will transfer power only to front wheels.

    It would be cheaper to get RA instead of swapping engines ;)
     
    LiX, Nov 8, 2009
    #4
  5. Carvs

    Carvs Active Member

    I'd definitely need a new clutch, however the rest of it comes with the engine. It's definitely no where near the price of a ralliart, plus I can do the work myself so I'll save big if all goes my way :).
     
    Carvs, Nov 9, 2009
    #5
  6. XxLaNcErGTSxX

    XxLaNcErGTSxX Well-Known Member

    here we go again
     
    XxLaNcErGTSxX, Nov 9, 2009
    #6
  7. Carvs

    Carvs Active Member

    Keep in mind that this is NOT about saving money or getting a cheap evo... I'm doing this because I want to, I want to build something, not buy it. It'll mean more that way and I'll enjoy it more. Sounds corny as hell, but I'm sure there are some who understand what I'm saying.
     
    Carvs, Nov 9, 2009
    #7
  8. ThunderOZ

    ThunderOZ Well-Known Member

    I say go for it. It seems like it would be an easier swap than if I tried it for my car...
     
    ThunderOZ, Nov 10, 2009
    #8
  9. Carvs

    Carvs Active Member

    Well I figure it has the same mounting points and whatnot, same frame and everything so it should just bolt up. I'm also looking into an AWD conversion from the EVO X
     
    Carvs, Nov 10, 2009
    #9
  10. enkrypter_DJ

    enkrypter_DJ Well-Known Member

    AWD conversion is more complex than everyone thinks, dont forget all the wires setup for your different AWD settings, then u need to go widebody unless u get custom made shorter axleshafts but then u wont be able to fit the tires as wide as on an X and the 300hp 4b11t is just wasted cause of poor grip form skinny tires, just like on the RA.

    Good luck with all the errors and CEL lights in the LCD display.

    Im for the 4b11t engine swap but forget the AWD conversion
     
    enkrypter_DJ, Nov 11, 2009
    #10
  11. XxLaNcErGTSxX

    XxLaNcErGTSxX Well-Known Member

    Just get another car. To do the Evo X AWD conversion it would cost you about $15,000 to get the ACD, AYC, and ASC systems
     
    XxLaNcErGTSxX, Nov 11, 2009
    #11
  12. kellcsi

    kellcsi New Member

    Hats off to you for taking on a good size project as this... There is a good sense of accomplishment on building your own projects.
    Good luck..
     
    kellcsi, Nov 11, 2009
    #12
  13. LiX

    LiX Well-Known Member

    Engine swap and AWD conversion... you waste your money.
     
    LiX, Nov 11, 2009
    #13
  14. vik2rius

    vik2rius Well-Known Member

    +1
    you'll just be waisting a pot load of money...if you have the money for a swap just use it and buy an EVO, it will save you a lot time...
    heck if i have the money, I wouldnt think twice of getting an EVO or an STI...
     
    vik2rius, Nov 11, 2009
    #14
  15. bambam

    bambam Well-Known Member

    i know you shouldnt beat a dead horse lol but yea the awd conversion is a little too much man. the engine swap is very interesting and unique but after that its just kinda...a waste lol but to each his own if you do it then shit man ill bow down and praise you for it haha
     
    bambam, Nov 11, 2009
    #15
  16. Carvs

    Carvs Active Member

    It's all about how much I can get the parts for, again I can do alot of the work myself and I highly doubt it'll cost anywhere near that amount of money. I'm already looking at under 5 for the engine, I'll have to see about the drivetrain though. It's a thought, I haven't started anything nor do I have the funds to do so at the moment but I'll keep you guys updated.
     
    Carvs, Nov 12, 2009
    #16
  17. EngRWW33

    EngRWW33 Well-Known Member

    ^^If this is something you follow through with, it will be an eye opening experience!!
     
    EngRWW33, Nov 12, 2009
    #17
  18. Carvs

    Carvs Active Member

    I'm sure it will be, I know it'll be a massive pain in the ass but if I am able to pull it off, it will be a massive accomplishment
     
    Carvs, Nov 17, 2009
    #18
  19. bambam

    bambam Well-Known Member

    any progress...?
     
    bambam, Nov 17, 2009
    #19
  20. ThunderOZ

    ThunderOZ Well-Known Member

    Have you researched all the differences between the 4b11 and 4b11t yet?
     
    ThunderOZ, Nov 17, 2009
    #20
Page 1 of 2